Automotive hail repair: The two techniques mentioned above will remove the majority of hail damage on your car, but a professional job at your local auto body shop is recommended for deep dents or badly damaged surfaces. The services tend to be cheap, fast and rarely require a new paint job. However, it is a good idea to compare prices and offered services at various body shops to see which package works best for your wallet and car’s situation.

First let’s start with some car paint care recommendations: For small dents on your car hood, a car dent repair kit may be a simple and inexpensive solution. You can easily find these kits at any local auto supply store and they are very user-friendly. Each kit often includes a knockdown tool, a glue gun and many stems for different sized dents. You may be surprised at the way the kit works and the professional result it makes. But we do recommend this kid for small dents only. For deep, large dents, it is better if you take your car to garage as the repair kit can not fix them and even cause more damage.

Don’t underestimate the necessary step of decontamination prior to application of your chosen wax. If you fail to do this step, you will get disappointing results regardless of the type of wax you have chosen. And yes…even that brand new car straight off the dealer lot will in have some form of pollutants already on the car paint from its travel from the factory to the car dealership. Clear coat is the top layer of your cars paint. It acts as a protective layer to filter out UV rays. But your clear coat is what you are trying to take care of with the above requirements. People get confused about clear coat vs. car paint. Virtually every car today is finished with a clear coat as the top layer. Think of it as car paint with no color added to it.

Not only can you unclog a drain with a plunger, but you can also get out small- to medium-sized dents out of your car too. Just splash some water on both the plunger and the dent and start pushing and pulling until it pops out. Make sure to use a cup plunger (for sinks), not a flange one (for toilets). Reversing into an object is one of the easiest ways to get a dent. So for plastic bumpers, even if you attempt to take off the bumper, it might still be difficult to push out the dent because of how stiff the plastic is. Solve this issue by boiling some water in a pot and throwing it on the dent.

Fixing Scratches: Apart from rust-proofing the vehicle, you should fix small scratches promptly. If the scratch is not too deep, you should only use touch up paint and finish off with a rubbing compound to get a good shine. If the scratch is deep and exposes the metal, you will have to sand off the surrounding paint and apply primer before painting the affected area. Read even more details at Automotive Repair & Customization in Colorado Springs.

If you are interested in learning how to do paintless dent repair, make sure that you take the time to gather the right tools and supplies, learn about the detailed process of PDR, and then spend time practicing your own repair techniques on metal panels from the local junk yard before you start doing repairs on your own vehicles.

So, we’ve explained what the procedure looks like — assuming it was done properly. And as you could probably guess there are a lot of ways an amateur or first-timer can get it wrong. It’s different than most other car repairs because it’s not about mechanical prowess; it’s more about control and the ability to maintain a steady hand and a gentle pace. You can’t rush it. The problem is, once a sheet metal repair starts to go awry, you’re usually much, much worse off than if you’d just left it alone. Metal holds its shape, but only to a certain point. Let’s say you get a dent in the hood — nothing too drastic, just a shallow, even dent with no sharp creases in an area that’s pretty easy to reach. You think it’ll be easy to pop it out on your own, so you begin to massage the underside while holding your shaping tool in place. You’ve made good progress so far, and a casual observer wouldn’t even notice the flawed area. But it’s not exactly perfect, and since it’s been fairly easy to this point, you decide to keep massaging the area to make it flawless. After a few more minutes of massaging, you realize that you’ve pushed it just a little too far. And now you’ve got this flabby area on the hood where you stretched out the metal. And there’s no easy way to shrink it back down. Keep going and it’ll stretch even more. Lesson learned.